Obvesti me
Artikla trenutno ni na zalogi. Spodaj se lahko prijavite in poslali vam bomo obvestilo, takoj ko artikel prispe na zalogo. Obvestilo boste dobili samo za ta artikel.
Vaš email naslov:
  CAPTCHA Image
Varnostna koda:

Pretraživanje
Hrvatski
Slovenski
Hrvatski
English
Deutsch
Italiano
Srpski
Prijava Registracija
NOVI ARTIKLI
AKCIJE
NAJPRODAVANIJI
Troškovi dostave
Odaberi državu
Austria
Belgium
Bosnia and Herzegovina
Bulgaria
Canada
Croatia
Cyprus
Czech Republic
Denmark
Estonia
Finland
France
Germany
Greece
Hungary
Ireland
Italy
Latvia
Lithuania
Luxembourg
Malta
Montenegro
Netherlands
Poland
Portugal
Romania
Serbia
Slovakia
Slovenia
Spain
Sweden
United Kingdom
Poštna dostava 5.00 EUR
 
Informacije
Uvjeti i informacije
Pitajte nas
Galago elektronika
Galago d.o.o.
Trg svobode 20
2390 Ravne na Koroškem
Slovenija
E-mail: info@galago.si
Telefon: 00386 (0)2 620 08 14
Telefon: 00386 (0)40 559 432
Facebook

THERMOCOUPLE AMPLIFIER WITH 1-WIRE BREAKOUT BOARD - MAX31850K, ADAFRUIT 1727

  Id broj: 575
Marka:ADAFRUIT
Zaliha:   DA
Cijena:19,94 €
senzorji ADAFRUIT Thermocouple Amplifier with 1-Wire Breakout Board - MAX31850K, Adafruit 1727
senzorji ADAFRUIT Thermocouple Amplifier with 1-Wire Breakout Board - MAX31850K, Adafruit 1727
senzorji ADAFRUIT Thermocouple Amplifier with 1-Wire Breakout Board - MAX31850K, Adafruit 1727
 

Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. So far Adafruit carried the MAX31855 which is an SPI interface thermocouple amplifier. The '855 is great but if you have a lot of thermocouples to measure it isn't terribly easy to use. That's why is Adafruit also carrying the new '850 model from Maxim - it's a "1-Wire" thermocouple amp which can have any number of breakouts on a single shared I/O line.

 

The MAX31850K does everything for you, and can be easily interfaced with any microcontroller that has 1-Wire support. This breakout board has the chip itself, a 3.3V regulator with 10uF bypass capacitors all assembled and tested. This board can be used with 'parasitic power' - where the power is on the data line - or with 'local power' where the power for the converter comes in on the Vin Pin.

 

Please note: this board does not have level shifting on the 3V Data line - we did this on purpose so that it can be used in parasitic mode. The data line must be level shifted to 3V - our 4-channel shifter works wonderfully for level shifting 1-Wire and you only need one at the '1-Wire host' for all thermocouples on the shared data line.

 

The MAX31850K data format is very similar to that of the well known 1-Wire DS18B20 temp sensor but it is not drop in compatible without code changes to check for the new '1 Wire family' type. Adafruit have adapted the classic Arduino OneWire and DallasTemp libraries to be MAX31850 compatible, so please click on those links to grab Adafruit libraries.

 

Comes with a 2 pin terminal block (for connecting to the thermocouple), 4.7K data line pullup resistor, and pin header (to plug into any breadboard or perfboard). Goes great with 1m K-type thermocouple. Not for use with any other kind of thermocouple, K type only!

 

- Works with any K type thermocouple

- Will not work with any other kind of thermocouple other than K type

- (-270°C to +1370°C) output in 0.25 degree increments

- Internal temperature reading

- 3.3 to 5v power supply. Data line is 3V only

- 1-Wire interface allows any number of thermocouple amps on a single data line